>> 自然科学版 >> 当期目录 >> 安全•矿业 >> 正文
分层裂隙煤体注浆改性后的力学特性
时间: 2026-11-20 次数:

赵忠明,陈嘉,王春,等.分层裂隙煤体注浆改性后的力学特性[J].河南理工大学学报(自然科学版),2027,46(1):1-9.

Zhao Z M, Chen J, Wang C, et al.Mechanical properties of stratified fractured coal after grouting modification[J].Journal of Henan Polytechnic University(Natural Science) ,2027,46(1):1-9.

分层裂隙煤体注浆改性后的力学特性

赵忠明1, 陈嘉1, 王春1,2, 李起航1, 张翼飞1

1.河南理工大学 能源科学与工程学院,河南 焦作  454003;2.中钢集团马鞍山矿山研究总院股份有限公司,安徽 马鞍山  243000

摘要: 目的  为了丰富分层裂隙煤体开采理论,开展分层裂隙煤体注浆改性后的力学特性研究。 方法  针对分层裂隙煤体开采中力学特性认识不足的问题,采用分层铺设不同颗粒粒度煤块并分层注浆的方法模拟并改性分层裂隙煤体,开展注浆改性后的轴向压缩力学试验研究。 结果  结果表明:煤块颗粒粒度、最小和最大颗粒层位对试样整体的变形趋势影响不大,应力-应变曲线都经历了下凹段→直线段→非线性段→陡降段4个阶段;注浆改性后分层裂隙煤体的抗压强度、弹性模量随煤块颗粒粒度的增大而减小,随最小、最大煤块颗粒层距试样主动受压端面的距离增大先减小后增大;颗粒粒度由[1,2) mm增至[10,20] mm的过程中,平均抗压强度由7.36 MPa降至5.11 MPa,降幅达30.6%;最小、最大煤块颗粒层在试样主动受压时,平均抗压强度分别为9.00,9.53 MPa,在试样被动受压时,平均抗压强度分别为7.99,8.48 MPa,降幅分别为11.2%和11.0%;在轴向压缩荷载作用下,注浆改性后的分层裂隙煤体率先在最大颗粒层萌发微裂隙,但裂隙多宏观起裂于试样受压产生应力集中的两端面,最终都以柱状劈裂破坏和单斜面压剪破坏为主,以混合摩擦性破坏为辅的形式产生宏观破坏。 结论  研究结果可为分层裂隙煤体的开采提供理论参考。

关键词:分层裂隙煤体;注浆改性;变形特性;抗压强度;破坏模式

doi:10.16186/j.cnki.1673-9787.2024010029

基金项目:国家自然科学基金资助项目(52274076);安徽省博士后科研计划资助项目(2022B650);中国博士后科学基金资助项目(2023M733279)

收稿日期:2024/01/10

修回日期:2024/05/09

出版日期:2026/11/20

Mechanical properties of stratified fractured coal after grouting modification

Zhao Zhongming1, Chen Jia1, Wang Chun1,2, Li Qihang1, Zhang Yifei1

1.School of Energy Science and Engineering, Henan Polytechnic University, Jiaozuo  454003, Henan, China;2.Sinosteel Maanshan General Institute of Mining Research Co., Ltd., Maanshan  243000, Anhui, China

Abstract: Objectives  This study investigates the mechanical properties of stratified fractured coal after grouting modification to provide a theoretical basis for its extraction. Methods To address the issue of insufficient understanding of the mechanical properties in the mining of layered fractured coal bodies, a method of layering coal blocks of different particle sizes and grouting layer by layer was used to simulate and modify layered fractured coal bodies, and axial compression mechanical tests were carried out after grouting modification. Results  The results show that coal particle size and the positions of the layers containing the smallest and largest particles have little influence on the overall deformation pattern of the specimens. All stress-strain curves exhibit four stages: an initial concave segment, a linear segment, a nonlinear segment, and a steep post-peak stress-drop segment. After grouting modification, the compressive strength and elastic modulus of the stratified fractured coal decrease with increasing coal particle size. As the distance between the actively loaded end face and either the layer containing the smallest particles or the layer containing the largest particles increases, both properties initially decrease and then increase. As the coal particle size increases from [1,2) mm to [10,20] mm, the average compressive strength decreases from 7.36 to 5.11 MPa, representing a reduction of 30.6%. When the layer containing the smallest particles and the layer containing the largest particles are located at the actively loaded end face, their corresponding average compressive strengths are 9.00 and 9.53 MPa, respectively. When these layers are located at the opposite end of the specimen, the corresponding average compressive strengths are 7.99 and 8.48 MPa, respectively, representing reductions of 11.2% and 11.0%, respectively. Under axial compressive loading, microcracks first initiate in the layer containing the largest coal particles. However, macroscopic cracks generally initiate near the two end faces of the specimens, where stress concentrations develop. The specimens ultimately fail primarily through columnar splitting and compression-shear failure along a single inclined plane, with mixed frictional failure as a secondary failure mode. Conclusion These findings provide a theoretical basis for the extraction of stratified fractured coal.

Key words:stratified fractured coal;grouting modification;deformation characteristics;compressive strength;failure modes

最近更新