| 时间: 2026-11-20 | 次数: |
支光辉,梁同同,刘少伟,等.矿用螺纹钢锚杆肋参数对锚固性能影响模拟研究[J].河南理工大学学报(自然科学版),2027,46(1):20-27.
Zhi G H, Liang T T, Liu S W,et al.Simulation study on the effects of rib parameters of rebar bolts on anchorage performance[J].Journal of Henan Polytechnic University(Natural Science) ,2027,46(1):20-27.
矿用螺纹钢锚杆肋参数对锚固性能影响模拟研究
支光辉1,2, 梁同同1, 刘少伟1,2
1.河南理工大学 能源科学与工程学院,河南 焦作 454003;2.河南理工大学 煤炭安全生产与清洁高效利用省部共建协同创新中心,河南 焦作 454003
摘要: 目的 针对煤矿深部开采巷道围岩易变形破坏问题,开展矿用螺纹钢锚杆肋部参数对锚固性能影响的研究。 方法 采用理论分析和数值模拟相结合方法,分析了锚杆横肋参数与锚固性能之间关系,确定了最佳横肋参数。 结果 模拟结果表明:锚杆在肋长度19.15 mm、肋高度1.8 mm 时,锚杆轴向应力达到最大值551.18 MPa,较普通锚杆提升9.94%;锚杆杆体锚固段轴向应力小于自由端,杆体轴向应力与锚杆肋高、肋长呈正相关。锚固体失效依次经历弹性阶段、短暂硬化阶段、硬化阶段和失效阶段,锚固剂在肋长度18.15 mm、肋高度1.00 mm时可承受26.99 MPa剪应力;锚固剂破坏最先发生在锚固端与横肋附近,横肋位置存在明显应力集中现象。正交试验敏感性分析显示,在锚杆肋宽、肋间距、肋坡角及螺纹上升角保持不变条件下,肋高对锚固力的影响程度大于横肋长度;当肋长19.15 mm、肋高2.4 mm 时,其载荷峰值为145.29 kN,比普通锚杆拉拔力提升4.09%。 结论 锚固体锚固力主要由锚固剂硬化阶段的承载能力决定。研究所得锚杆横肋参数规律可为现场锚杆结构设计与选型提供参考依据。
关键词:螺纹钢锚杆形态参数;数值模拟;锚固性能;正交试验;锚杆支护
doi:10.16186/j.cnki.1673-9787.2024030043
基金项目:国家自然科学基金资助项目(52074102);中原科技创新领军人才项目(244200510013);河南省高校科技创新团队研究项目(23IRTSTHN007);河南理工大学博士基金资助项目(B2022-53)
收稿日期:2024/03/15
修回日期:2024/07/17
出版日期:2026/11/20
Simulation study on the effects of rib parameters of rebar bolts on anchorage performance
Zhi Guanghui1,2, Liang Tongtong1, Liu Shaowei1,2
1.School of Energy Science and Engineering, Henan Polytechnic University, Jiaozuo 454003, Henan, China;2.State Collaborative Innovation Center of Coal Work Safety and Clean-efficiency Utilization, Jiaozuo 454003, Henan, China
Abstract: Objectives To address the susceptibility of surrounding rock in roadways to deformation and failure during deep coal mining, this study investigates the effects of the rib parameters of rebar rock bolts on their anchorage performance. Methods Theoretical analysis and numerical simulation were combined to examine the relationship between transverse rib parameters and anchorage performance and to determine the optimal rib parameters. Results The simulation results show that when the rib length and rib height are 19.15 mm and 1.8 mm, respectively, the maximum axial stress in the bolt reaches 551.18 MPa, an increase of 9.94% over that of a conventional bolt. The axial stress in the anchored section of the bolt shank is lower than that at the free end, and the axial stress in the shank increases with rib height and rib length. The failure process of the anchoring medium proceeds through four stages: elasticity, brief hardening, hardening, and failure. The anchoring medium can withstand a shear stress of 26.99 MPa when the rib length and rib height are 18.15 mm and 1.00 mm, respectively. Failure of the anchoring medium initiates near the anchorage end and around the transverse ribs, where pronounced stress concentrations occur. Sensitivity analysis based on orthogonal experiments indicates that, with rib width, rib spacing, rib inclination angle, and thread lead angle held constant, rib height has a greater effect on anchorage force than rib length. When the rib length is 19.15 mm and the rib height is 2.4 mm, the bolt pull-out force reaches a maximum of 145.287 kN, an increase of 4.09% over that of a conventional bolt. Conclusions The anchorage force of the anchoring system is primarily governed by the load-bearing capacity of the anchoring medium during its hardening stage. The findings on the effects of transverse rib parameters can provide a reference for the structural design and selection of rock bolts in field applications.
Key words:rebar bolt geometric parameters;numerical simulation;anchorage performance;orthogonal experiments;rock bolt support