>> 自然科学版 >> 当期目录 >> 安全•矿业 >> 正文
基于均匀设计法砂岩相似材料配比及显著性研究
时间: 2026-11-20 次数:

李重情,汤皓朋,许镇,等.基于均匀设计法砂岩相似材料配比及显著性研究[J].河南理工大学学报(自然科学版),2027,46(1):40-47.

Li Z Q, Tang H P , Xu Z, et al.Study on the proportioning and significance analysis of sandstone-like materials based on uniform design[J].Journal of Henan Polytechnic University(Natural Science) ,2027,46(1):40-47.

基于均匀设计法砂岩相似材料配比及显著性研究

李重情1,2, 汤皓朋1, 许镇1, 岳廷乐1

1.安徽理工大学 安全科学与工程学院,安徽 淮南  232001;2.深部煤矿采动响应与灾害防控国家重点实验室,安徽 淮南  232001

摘要: 目的 为了寻找符合原岩强度的相似材料配比方案,探究相似材料密度、灰膏比、养护天数与试件单轴抗压强度之间的关系,以张集矿1615A工作面的中细砂岩为研究对象展开研究。 方法  利用河砂、石灰、石膏、水为原料,采用均匀设计法设计试验方案;根据试验因素和水平,采用拟水平法改良均匀设计表并建立回归模型;通过SPSS软件拟合出单轴抗压强度回归方程,并对其进行显著性检验。 结果 结果表明:均匀设计法能细分密度、灰膏比、养护天数因素水平而不增加工作量,对比正交试验,其优点在于各因素水平数不必一致,试验点代表性强,即采用10组试验的数据结果等价于25组正交试验结果,其中相似材料试件密度为1.45~1.63 g/cm3,单轴抗压强度为0.110~0.351 MPa,可得原岩和相似试件的容重比为1.542~1.675,推算出原岩强度为16.96~58.79 MPa,范围较广;结合张集矿1615A工作面中细砂岩力学参数可得到相似材料最优配比方案;通过F检验、拟合度分析、显著性分析、共线性分析等方法验证单轴抗压强度回归方程的有效性;由显著性分析可知,影响单轴抗压强度各因素的主次顺序依次为密度、养护天数、灰膏比。 结论  基于改良均匀设计表的均匀设计法可为后续类岩石相似材料配比的试验方案优化设计提供借鉴。

关键词:相似模拟;均匀设计;SPSS软件;细砂岩;显著性分析

doi:10.16186/j.cnki.1673-9787.2024040040

基金项目:国家自然科学基金资助项目(52374179,52227901)

收稿日期:2024/04/24

修回日期:2024/07/17

出版日期:2026/11/20

Study on the proportioning and significance analysis of sandstone-like materials based on uniform design

Li Zhongqing1,2, Tang Haopeng1, Xu Zhen1, Yue Tingle1

1.School of Safety Science and Engineering, Anhui University of Science and Technology, Huainan  232001, Anhui,  China;2.State Key Laboratory of Mining Response and Disaster Prevention and Control in Deep Coal Mines, Huainan  232001, Anhui, China

Abstract: Objectives To determine a mix proportion for similar materials that reproduces  the strength of the original rock and to investigate the relationships between material density, the lime-to-gypsum ratio, curing duration, and the uniaxial compressive strength of specimens, medium- to fine-grained sandstone from the 1615A working face of Zhangji Coal Mine was selected as the study material. Methods  River sand, lime, gypsum, and water were used as raw materials, and the experimental program was designed using the uniform design method. The uniform design table was modified using a quasi-level method to accommodate the selected experimental factors and levels, and a regression model was established. A regression equation for uniaxial compressive strength was fitted using SPSS software, and its statistical significance was evaluated. Results  The uniform design method allows finer gradation of the levels of density, lime-to-gypsum ratio, and curing duration without increasing the experimental workload. Compared with the orthogonal experimental design, its advantages include the flexibility to assign different numbers of levels to different factors and the high representativeness of the selected experimental points. Specifically, the results from 10 experimental groups were equivalent to those from 25 groups in an orthogonal experimental design. The densities of the similar-material specimens ranged from 1.45 to 1.63 g/cm3, and their uniaxial compressive strengths ranged from 0.110 to 0.351 MPa. The ratio of the bulk density of the original rock to that of the similar-material specimens ranged from 1.542 to 1.675. Based on this ratio, the corresponding strength of the original rock was estimated to range from 16.96 to 58.79 MPa, indicating that the proposed mix proportions are applicable over a relatively broad range of original-rock strengths. The optimal mix proportion was determined by incorporating the mechanical parameters of the medium- to fine-grained sandstone at the 1615A working face of Zhangji Coal Mine. The validity of the regression equation for uniaxial compressive strength was verified through the F-test, goodness-of-fit analysis, statistical significance analysis, and multicollinearity analysis. The significance analysis ranked the factors influencing uniaxial compressive strength in descending order of importance as follows: density, curing duration, and lime-to-gypsum ratio. Conclusions  The uniform design method based on a modified uniform design table can provide a reference for optimizing experimental designs for the mix proportioning of rock-like similar materials in subsequent studies.

Key words:similar-material simulation;uniform design;SPSS software;fine sandstone;significance analysiss

最近更新