| 时间: 2026-11-20 | 次数: |
虞爱平,刘涛,刘利源,等.在役RC柱声发射信号传播特性研究[J].河南理工大学学报(自然科学版),2027,46(1):166-172.
Yu A P, Liu T, Liu L Y,et al.Propagation characteristics of acoustic emission signals in in-service RC columns[J].Journal of Henan Polytechnic University(Natural Science) ,2027,46(1):166-172.
在役RC柱声发射信号传播特性研究
虞爱平1, 刘涛1, 刘利源1, 苗天娇1, 虞小平2
1.桂林理工大学 广西绿色建材与建筑工业化重点实验室,广西 桂林 541004;2.桂林理工大学南宁分校,广西 崇左 532100
摘要: 目的 为明确在役RC柱中声发射信号的传播特征,开展在役RC柱声发射检测试验。 方法 通过声发射幅值参数、能量参数、中心频率参数、快速傅里叶变换、小波包变换分析不同传播距离下在役RC柱声发射信号衰减规律。 结果 试验结果表明:传播距离小于500 mm时,声发射信号能量、幅值、中心频率随传播距离增加整体呈衰减趋势;大于500 mm时几乎不再衰减,对能量参数进行负指数拟合,其衰减系数为0.009 3;信号传播至400 mm时,波的主要成分开始发生剧烈变化,传播至500 mm时,波的主要成分完全改变,波型改变,且传播距离大于500 mm时,传感器接收的信号包含大量噪音波;声发射频域信号的主频随传播距离增加由高频向低频逐渐转移;传播距离小于200 mm时,高频带信号能量向低频带转移较快,低频带信号能量占比随传播距离增加呈持续上升趋势;当信号传播至700 mm时,频带1能量占比达到95.98%。 结论 随着传播距离增加,在役RC柱中声发射信号有效高频成分衰减,主导波成分发生转换,不同传感器接收信号的可比性削弱,影响声发射源定位。为保证传感器接收信号以同类波为主,建议在役RC柱声发射检测中相邻传感器间距控制在400 mm内。
关键词:在役RC柱;幅值;能量;中心频率;快速傅里叶变换;小波包变换
doi:10.16186/j.cnki.1673-9787.2024080040
基金项目:国家自然科学基金资助项目(51968014);广西研究生教育创新计划项目(YCSW2024359);广西自然科学基金资助项目(2022GXNSFAA035553)
收稿日期:2024/08/23
修回日期:2024/11/14
出版日期:2026/11/20
Propagation characteristics of acoustic emission signals in in-service RC columns
Yu Aiping1, Liu Tao1, Liu Liyuan1, Miao Tianjiao1, Yu Xiaoping2
1.Guangxi Key Laboratory of Green Building Materials and Construction Industrialization,Guilin University of Technology, Guilin 541004, Guangxi, China;2.Guilin University of Technology at Nanning, Chongzuo 532100, Guangxi, China
Abstract: Objectives To clarify the propagation characteristics of acoustic emission (AE) signals in in-service reinforced concrete (RC) columns, AE monitoring tests were conducted on in-service RC columns. Methods The attenuation characteristics of AE signals at different propagation distances were investigated based on AE amplitude, energy, and center-frequency parameters, as well as fast Fourier transform (FFT) and wavelet packet transform (WPT). Results The experimental results show that, when the propagation distance is less than 500 mm, the energy, amplitude, and center frequency of the AE signals generally decrease with increasing propagation distance; when the propagation distance exceeds 500 mm, these parameters exhibit little further attenuation. A negative exponential fit of the energy parameter gives an attenuation coefficient of 0.009 3. At a propagation distance of 400 mm, the principal components of the wave begin to change substantially; at 500 mm, the principal wave components change completely, accompanied by a change in waveform. When the propagation distance exceeds 500 mm, the signals received by the sensors contain a substantial amount of noise. In the frequency domain, the dominant frequency of the AE signals gradually shifts from high to low frequencies as the propagation distance increases. When the propagation distance is less than 200 mm, the energy of the high-frequency components transfers rapidly to the low-frequency components, and the proportion of energy in the low-frequency band continuously increases with propagation distance. When the propagation distance reaches 700 mm, the energy proportion of frequency band 1 reaches 95.98%. Conclusions With increasing propagation distance, the effective high-frequency components of AE signals in in-service RC columns attenuate, accompanied by a transition in the dominant wave components. This reduces the comparability of signals received by different sensors and may affect AE source localization. To ensure that the signals received by adjacent sensors are dominated by the same type of wave, the spacing between adjacent sensors should be controlled within 400 mm during AE testing of in-service RC columns.
Key words:in-service RC column;amplitude;energy;center frequency;fast Fourier transform (FFT);wavelet packet transform (WPT)